By December 18, 2014 0 Comments Read More →

Pressure Vessel and Piping Design

Pressure Vessel and Piping Design

Dafam Fortuna Hotel, Yogyakarta | 05 – 08 May 2015 | IDR 7,000,000
Dafam Fortuna Hotel, Yogyakarta | 15 – 18 Juni 2015 | IDR 7,000,000
Dafam Fortuna Hotel, Yogyakarta | 23 – 26 September 2015 | IDR 7,000,000
Dafam Fortuna Hotel, Yogyakarta | 27 – 30 October 2015 | IDR 7,000,000



DESCRIPTION

In order to address the safety concerns associated with pressurized equipment and piping, these are required to be designed, fabricated and operated according to specified codes and standards. The commonly accepted codes are the ASME Sec. VIII Div. 1 for design of pressure vessels and ANSI B31.1 for design of piping. It takes a new engineer considerable time to understand that there is much more to pressure vessel design than calculation of hoop stress. The present course is designed to bridge the gap between the theoretical aspects of pressure vessel design and its industrial application. The faculty of this course would share their considerable experience to address the practical issues associated with pressure vessel design.


WHO SHOULD ATTEND

The course is aimed at engineers from Engineering and Manufacturing organizations who are involved in design and fabrication of pressure vessel and piping. It is anticipated that participants hold an engineering degree or have been involved for a good number of years in the design of vessels and piping. This course will be particularly appropriate for new engineers needing initial familiarity with application of ASME Code to the design and construction of pressure vessel and piping. It is also useful for engineers who have some experience of pressure vessel equipment and who wish to broaden their understanding of the behaviour of pressurized equipment.



PRESSURE VESSEL & PIPING DESIGN SUMMARY OUTLINE

  1. Introduction to Pressure Vessel Design Codes
  2. Design Basis and Design Criteria
  3. Design for Internal pressure
  4. Design for External Pressure
  5. Design of Nozzles
  6. Flange design
  7. Design of Vessel supports
  8. Design of Tubesheets
  9. Fabrication
  10. Examination
  11. Testing
  12. Computer codes for pressure vessel design
  13. Case studies on failure of pressure vessels
  14. Materials of construction for pressure vessels
  15. Design of piping as per ANSI B31.1
  16. Pressure, thermal and dynamic loads
  17. System layout
  18. Pipe supports and restraints
  19. Piping flexibility, Flexibility factor and stress intensification factor
  20. Computer codes for Piping analysis



COURSE METHOD

  • Presentation
  • Discuss
  • Case Study
  • Evaluation
  • Simulation



TIME & VENUE

  • Dafam Fortuna Hotel Jl. Dagen 60 Malioboro Yogyakarta,
  • 05 – 08 May 2015
  • 15 – 18 Juni 2015
  • 23 – 26 September 2015
  • 27 – 30 October 2015
    4 days (08 am – 04 pm)



COURSE SPEAKER

Teguh Pudji Purwanto, Ir, MT
Teguh Pudji Purwanto experienced more than 26 years in mechanical industry.



COURSE FEE

IDR 7,000,000.00 per participant non residential



FACILITY

  • Module / Handout Pressure Vessel and Piping Design Training
  • Certificate
  • Souvenir
  • Training Kit

Formulir Permintaaan Informasi Lanjutan / Pra-Pendaftaran Public Training
  1. INFORMATION OPTIONS
  2. (required)
  3. (required)
  4. PERSONAL DATA
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. PRE REGISTRATION DATA (Tidak Mengikat)
  12. (required)
  13. MESSAGE FOR TRAINING PROVIDER
 

cforms contact form by delicious:days

About the Author:

Post a Comment