Electrical & Mechanical Rotating Equipment

Workshop exercises in which machines are chosen to meet an outline brief for a pump or compressor

Jadwal Training 2019 Selanjutnya …

Deskripsi Training Electrical & Mechanical Rotating Equipment

This course is an integral part of the programme, has a duration of few days, and covers equipment driven directly by gas turbines or indirectly through gas turbine driven generator sets, electrical power systems and motor drivers. Typical applications are for Oil, Gas and other industries.

Tujuan Training Electrical & Mechanical Rotating Equipment

Workshop exercises in which machines are chosen to meet an outline brief for a pump or compressor plant with the appropriate direct or electric motor drive and its control system will be undertaken.

Materi Training Electrical & Mechanical Rotating Equipment

Gas Turbine Engines
- The basic principles underpinning the operation of the gas turbine will be presented. This section will also include a description of the following cycles:- simple, reheat, recuperated, inter-cooled, combined gas and steam and steam injected. The effects of engine rating, variation in efficiencies between engines, maintenance intervals and fuel quality are introduced.
Pumps and Compressors
- The basic principles of rotor dynamic and positive displacement pumps and compressors and the effects of cavitation, compressibility, viscosity variation and humidity. Losses in fluid systems and interaction between machines and systems. Introduction to the basic design principles of pumps and compressors, involving shafts, bearings and seal systems. A discussion of the regulation of pumps and compressors. The correct selection and application of pumps and compressors.
Electrical Power Systems
- Power System Design covering voltage and frequency control, maximum and minimum system fault levels. A demonstration of power system simulation by computer studies including load flow, voltage drop, short circuit levels, motor starting performance and protection grading.
Electrical Power Generation
- An overview of the electrical features of power generation. The mechanical engineer is involved as a member of a design team, often as the lead engineer, with the important requirement of discussing electrical design features with specialist engineers and then being expected to take part in the decision making process for a power generation package. Design, construction and specification of synchronous machines (generators) with typical data sheets.
Electric Motors Drive Systems
- Design and construction features of asynchronous machines (motors), load characteristics, active and reactive load sharing, power transfer between power systems. Matching motors to the driven equipment and effect of power supply system variations. Specifications in relation to IEC/BSS standards. Data sheets for the selection and purchase of electrical machines. Electrical Variable Speed Drive Systems with power electronics and various types of convertors, applications to motors and generators, effect on driven equipment. Data sheets for the selection and purchase of systems.
Aspects of Electrical Machines
- Hazardous area protection, electrical power three phase calculations with worked examples and typical values that can be used during project evaluations. Operation and Maintenance plans and common failures. Digital microprocessor systems interfacing with plant control systems for the control, protection and retained information on motor performance.
Selection of Drivers
- When driving rotating equipment a key aspect of any project is the decision on whether pumps or compressors are to be driven by gas turbine engines or by electric motors from a power system with the option of local gas turbine driven power generation. Each project will always have its own particular solution.

Metode

Presentasi, lecture, studi kasus, tanya jawab, brainstorming, diskusi.

Jadwal Training 2019

Hotel Santika Kuta, Bali
Hotel Nagoya Plaza, Batam
Hotel Fave, Balikpapan
Hotel Aston, Manado
Hotel Lombok Raya, Mataram
Hotel 101 Dago , Bandung
Hotel Santika Pandegiling, Surabaya
Hotel Ibis Kemayoran , Jakarta
Hotel Ibis Solo
Hotel Ibis Simpang Lima, Semarang
Hotel Melia Purosani, Yogyakarta
19 – 20 Agustus 2019
26 -27 Agustus 2019
02 – 03 September 2019
09-10 September 2019
16 – 17 September 2019
23 – 24 September 2019
30 September – 01 Oktober 2019
07 – 08 Oktober 2019
14 – 15 Oktober 2019
21 – 22 Oktober 2019
28 – 29 Oktober 2019
04 – 05 November 2019
11 – 12 November 2019
18 – 19 November 2019
25 – 26 November 2019
02 -03 Desember 2019
09 – 10 Desember 2019
16 – 17 Desember 2019
23 – 24 Desember 2019
30 – 31 Desember 2019

Investasi dan Fasilitas Training

Rp 8.400.000 (Non Residential, Belum Terasuk Pajak PPn 10%) untuk lokasi di Bali, Batam, Balikpapan, Manado atau Lombok
Rp 7.400.000 (Non Residential, Belum Terasuk Pajak PPn 10%)) untuk lokasi di Bandung, Jakarta atau Surabaya
Rp 6.400.000 (Non Residential, Belum Terasuk Pajak PPn 10%) untuk Lokasi Solo, Semarang atau YogyakartaQuota minimum 2 peserta
Fasilitas: Certificate,Training kits, USB, Lunch, Coffe Break, Souvenir
Untuk peserta luar kota disediakan transportasi antar-jemput dari Bandara/Stasiun ke Hotel khusus bagi perusahaan yang mengirimkan minimal 3 orang peserta)

Instruktur

Tugino, ST.,MT dan Tim