INTERNAL AND EXTERNAL CORROSION CONTROL AND MONITORING FOR PIPELINE AND SURFACE FACILITY (Pasti Jalan)

INTERNAL AND EXTERNAL CORROSION CONTROL AND MONITORING FOR PIPELINE AND SURFACE FACILITY
Bandung | 11 – 14 August 2015 | Rp 8.750.000/person
Bandung | 07 – 10 September 2015 | Rp 8.750.000/person
Bandung | 06 – 09 October 2015 | Rp 8.750.000/person
Bandung | 09 – 12 November 2015 | Rp 8.750.000/person
Bandung | 15 – 18 December 2015 | Rp 8.750.000/person

 

INTRODUCTION :

Corrosion control and monitoring course focuses on corrosion – from either internal or external source – and its potential problem, and the protection methods to stop or control them. Review on corrosion and technique by which it can be identified, monitored and controlled will be given in detail. Active participation is encouraged through case studies and examples especially on the use of painting and coatings, transformer-rectifier of impressed current, magnesium, zinc and alum sacrificial anodes for external protection, and the injection of corrosion inhibitors and biocides for internal corrosion control.

PRE-REQUISITE :

NONE. No previous training in corrosion control is required. However, to gain the most from this course, a basic understanding of physics, chemistry and basic unit operations will be helpful.

TRAINING MATERIAL OUTLINE :

1. Review of oil & gas surface production facility and operations.
2. Review of metallic materials used in surface production facility and pipelines and the corrosion problem usually happen.
3. Case studies and examples of oil & gas material failure caused by corrosion from internal and external source.
4. Uniform, galvanic and localized corrosion failures.
5. Internal corrosion of pipeline, vessel and processing equipment caused by sour component, H2S, CO2, organic acid, brine, and the SRB (sulfate reducing bacteria).
6. External corrosion of underground, underwater and under-seawater pipeline and structure caused by impurities in soil and water environment.
7. External corrosion of topside structure caused by marine atmosphere.
8. Basic electrochemistry of corrosion process, Ohm’s law and the corrosion rate.
9. Corrosion control and prevention with painting & coatings and the cathodic protection.
10. Measurement of corrosion potential and corrosion current.
11. Protection with sacrificial anode and impressed current.
12. Understanding NACE Standard RP-01-69 to stop external corrosion attack.
13. Requirement, design and criteria of cathodic protection.
14. Sacrificial anode specification, installation and construction.
15. Testing, monitoring, and inspection of cathodic protection.
16. Inspection and maintenance of transformer-rectifier and sacrificial anode.
17. Field test, measurement techniques and instrument.
18. Data recording and evaluation of cathodic protection system.
19. Case studies of corrosion control and prevention with cathodic protection.
20. Internal corrosion problem in the pipeline and surface facility.
21. Oil/gas/water fluid properties and the corrosion tendency.
22. Deterioration by H2S, CO2, and acidic corrosive components.
23. Pipeline leakage and rupture by microbial induced corrosion.
24. Corrosion caused by SRB and the pitting mechanism.
25. Corrosion caused by oxygen penetration.
26. Examples and case studies of equipment corrosion damage and pipeline leakage.
27. Understanding NACE Standard RP-0775 for internal corrosion control and monitoring.
28. Practical internal corrosion monitoring methods.
29. Access fittings, corrosion coupon and corrosion probes.
30. Practical internal corrosion control and prevention methods.
31. Internal corrosion control with inhibitors and the selection of suitable corrosion inhibiting chemicals.
32. Dosage and injection methods of corrosion inhibitors.
33. SRB control with biocides and the selection of suitable and low risk biocide formula.
34. Dosage and injection methods of biocides.
35. Oxygen control by de-aeration and chemical injection, and the selection of suitable oxygen scavenger chemicals.
36. Dosage and injection methods of oxygen scavenger.
37. Safety in the use of chemicals for internal corrosion prevention.
38. Review of gas dehydration process and operations.
39. Internal corrosion problem in glycol contactor (dehydration) unit.
40. Method and materials use to control the corrosiveness of rich glycol solution.
41. Review of amine sweetening process and operations.
42. Internal corrosion problem in amine sweetening unit.
43. Method and materials use to control the corrosiveness of rich amine solution.
44. Examples and case studies of internal corrosion control

TRAINING INSTRUCTOR

Ir. Hilman Ahmad, DCE

Ir. Hilman Ahmad, DCE., an Independent Consultant in industrial oil and gas, member of the Society of Indonesian Petroleum Engineers, who manage the Industrial Oil & Gas Education Center for Professionals and has been practicing production operation & safety and corrosion control engineering in Indonesia for more than twenty-five years. He post-graduated from Tokyo Institute of technology (sponsored by UNESCO) in 1977. He joined in-field-practice program at Nippon Kokan Steel Company & Research Center Kawasaki, Japan for production facility design & construction and corrosion prevention & control in 1983, and collaborated with Cormon Industrial Research Center Brighton UK for on-line corrosion monitoring development in 2000.He has been delivering consultative course in production operation, maintenance & safety and corrosion control for personnel from Oil & Gas Company and Petrochemical Industry since 1979.

VENUE :

Bandung (Golden Flower, Banana Inn, Grand Seriti, Carrcadin, Amaroossa, Grand Serela, Gino Feruci, Verona Palace, Malaka, Zodiac Taurus)

TRAINING DURATION :

4  days

 

 

TRAINING TIME :

1. 12 Jan 2015-15 Jan 2015
2. 10 Feb 2015-13 Feb 2015
3. 09 Mar 2015-12 Mar 2015
4. 06 Apr 2015-09 Apr 2015
5. 05 May 2015-08 May 2015
6. 09 Jun 2015-12 Jun 2015
7. 30 Jun 2015-03 Jul 2015
8. 11 Aug 2015-14 Aug 2015
9. 07 Sep 2015-10 Sep 2015
10. 06 Oct 2015-09 Oct 2015
11. 09 Nov 2015-12 Nov 2015
12. 15 Dec 2015-18 Dec 2015

 

 

INVESTATION PRICE/ PERSON :

1. Rp 8.750.000/person (full fare)  or
2. Rp 8.500.000/person (early bird, payment 1 week before training) or
3. Rp 8.250.000/person (if there are 3 persons or more from the same company)

 

 

FACILITIES FOR PARTICIPANTS :

1. Training Module
2. Flash Disk contains training material
3. Certificate
4. Stationeries: NoteBook and Ballpoint
5. T-Shirt
6. Bag
7. Training Photo
8. Training room with Full AC facilities and multimedia
9. Lunch and twice coffeebreak every day of Corrosion control training
10. Qualified Instructor
11. Transportation for participants from hotel of participants to/from hotel of training – VV (if minimal participants is 4 persons from the same company)

RECOMMENDATION TO PARTICIPANTS :

Participants are recommended to bring laptop for practice sessions

Formulir Permintaaan Informasi Lanjutan / Pra-Pendaftaran Public Training

1. INFORMATION OPTIONS
2. Judul Training(required)
3. Tanggal Training
4. Select a message type Registration Offering Letter (Permintaan Proposal Penawaran) Next Schedule Information (Jadwal selanjutnya) More Information (Informasi tambahan) Others (lain-lain) (required)
5. PERSONAL DATA
6. Your Name(required)
7. Job Title(required)
8. Company(required)
9. Company Address
10. Email(valid email required)
11. Mobile Phone(required)
12. Office Phone(required)
13. Extention No.
14. Facsimile (Fax)
15. Website
16. PRE REGISTRATION DATA (Tidak Mengikat)
17. Penanggung Jawab Training di Perusahaan
18. Email
19. Office Phone+Ext atau No. Handphone
20. Jumlah Peserta(required)
21. Nama-nama peserta
22. Payment Method Bank Transfers Submitting an Invoice Cheque or Cash on arrival ( If Possible)
23. MESSAGE FOR TRAINING PROVIDER
24. Pesan untuk penyelenggara Training
25. CC this registration / message to me

 

cforms contact form by delicious:days